英语翻译帮忙翻译下面的一段软件的安装说明1.SolidCAM 2010 HF1 SP2 Setup1.1.To install SolidCAM 2010 HF1 SP2 run ..\Setup.exe2.USB-HASP-Emulator Setup2.1.If you already have got installed and working previous versions of SolidCAM2009

英语翻译帮忙翻译下面的一段软件的安装说明1.SolidCAM 2010 HF1 SP2 Setup1.1.To install SolidCAM 2010 HF1 SP2 run ..\Setup.exe2.USB-HASP-Emulator Setup2.1.If you already have got installed and working previous versions of SolidCAM2009
英语翻译
帮忙翻译下面的一段软件的安装说明
1.SolidCAM 2010 HF1 SP2 Setup
1.1.To install SolidCAM 2010 HF1 SP2 run ..\Setup.exe
2.USB-HASP-Emulator Setup
2.1.If you already have got installed and working previous versions of SolidCAM2009-2010 with USB-HASP-Emulator you need to install SolidCAM2010 HF1 SP2 only.
2.2.If you have no got SolidCAM2009-2010 installed and working but you've got USB-HASP-Emulator installed (USB-HASP-Emulator with service vusbbus.sys,mcamvusb.sys or any other service using for dumps Window Registry [HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\NewHasp\Services\Emulator\HASP\Dump\] ) you do not need to install Emulator.Just register the dump (run "solidcam2010.reg") and restart or reinstall your Emulator
2.3.If you have no got USB-HASP-Emulator installed you need to install it
ATTENTION!
To install emulator you need Administrator rights!
To install emulator for Win Vista or Win7 you need to boot computer in mofe F8 > Enable Enforcement Unsigned drivers!
Moreover you need to use boot mode F8 > Enable Enforcement Unsigned drivers at every reboot of computer!
2.3.1.Copy folder USB-Emul_Win64 to C:
2.3.2.Register dump (run ..\USB-Emul_Win64\solidcam2010.reg" and confirm to add info in Windows Registry)
2.3.3.Run Start -> Control Panel -> Add Hardware (Yes,I have already connected the hardware) -> Add a new hardware device -> Install the hardware that I manually select from a list -> Show all Devices -> Have disk -> Browse -> (browse to folder "USB-Emul_Win64") -> OK -> Confirm to install not certificated drivers if Windows ask for..
If setup is succesfull you have to see new devices:
Device Manager -> System devices -> Virtual Usb Bus Enumerator
Device Manager -> Universal Serial Bus controllers ->SafNet inc.HASP key
Device Manager -> Universal Serial Bus controllers ->SafNet inc.USB key
That is all
That's all

英语翻译帮忙翻译下面的一段软件的安装说明1.SolidCAM 2010 HF1 SP2 Setup1.1.To install SolidCAM 2010 HF1 SP2 run ..\Setup.exe2.USB-HASP-Emulator Setup2.1.If you already have got installed and working previous versions of SolidCAM2009
1.SolidCAM的2010年HF1 SP2安装
1.1.SolidCAM的2010 HF1要安装SP2的运行..\的Setup.exe
2.USB的的HASP仿真器安装
2.1.如果你已经得到了安装和工作SolidCAM2009 - 2010以前版本的USB -的HASP仿真器,您需要安装SolidCAM2010 HF1 SP2的唯一.
2.2.如果你没有得到SolidCAM2009 - 2010安装和工作,但你得的USB的HASP仿真器安装（与服务vusbbus.sys,mcamvusb.sys或任何其他服务的USB的HASP仿真器窗口的转储注册表[HKEY_LOCAL_MACHINE \系统使用\ CurrentControlSet \ NewHasp \服务\模拟器\的HASP \转储\]）,你不需要安装模拟器.只需注册转储（运行“solidcam2010.reg”）,并重新启动或重新安装你的模拟器
2.3.如果你没有得到的USB的HASP仿真器安装,您需要安装它
注意!
若要安装模拟器,你需要管理员的权利!
若要安装模拟器运Vista或Win7的你需要在财政经济部启动按F8>“启用执行未签名驱动程序的计算机!
此外,您需要使用的每一个引导模式重新启动计算机按F8>“启用执行未签名驱动程序!
2.3.1.复制文件夹的USB Emul_Win64到C：
2.3.2.寄存器转储（运行..\ USB的Emul_Win64 \ solidcam2010.reg“,并确认在Windows注册表中添加信息）
2.3.3.运行开始 - >“控制面板” - >添加硬件（是的,我已经连接了此硬件） - >“添加新的硬件设备 - >”安装我手动的硬件列表中选择 - >“显示所有设备 - >”从磁盘安装“ - >浏览“ - >（浏览到文件夹”USB - Emul_Win64“） - >”确定“ - >确认要安装未认证驱动程序如果Windows要求..
如果安装程序succesfull你必须看到新的设备：
设备管理器 - >“系统设备 - >”虚拟USB总线枚举
设备管理器 - >“通用串行总线控制器” - > SafNet公司.HASP锁
设备管理器 - >“通用串行总线控制器” - > SafNet公司.USB